DIY Audio Projects Forum
 NEW  Matt presents bias and operation data for the 6V6 tube in SE operation - 6V6 Single-Ended (SE) Ultra Linear (UL) Bias Optimization.

DIY Audio Projects Forum

Welcome to the DIY Audio Projects Message Forum. Use these forums to discuss Hi-Fi audio and to share your DIY Audio Projects. Registration is free and required to post messages and view the file attachments. Registration will only take a minute and registered users do not see any advertisements. After you have completed the online registration process, check your email (including spam/junk folder) for the verification email to activate your account. New members are under moderation - so your posts will not be visible until approved by a moderator. See the Read Me 1st, Forum RULES and Forum FAQ to get started on the forum.

It is currently 03 Dec 2020, 09:26

All times are UTC - 6 hours [ DST ]




Post new topic Reply to topic  [ 3 posts ] 
Author Message
 Post subject: Phono Preamp Wiring
PostPosted: 11 Apr 2020, 22:44 
Offline

Joined: 18 Sep 2019, 21:25
Posts: 1
Still learning, but had a general question hopefully the forum could answer.
I'm wondering about preamp and wiring to a receiver roughly 35ft away.
Some background:
I've been looking for a project to learn more about electrical engineering and circuit design.
Ended up finding a kit for a preamp to replace the LP-120's built in preamp (more for fun than sound quality).
Problem:
From the output stage of the preamp, I'd have to run the wire through my walls and down to my home receiver. (S.O. only wants one 'set' of speakers/amp in the room)
Doing some research, I've hit a snag as to what would it be best to run from component to component, balanced or unbalanced lines for best audio quality.

Which setup the forum recommend, and how would that look in application?

Additional info:
The preamp kit in question only provides RCA in/out and a ground lug.
External noise in my area is noticeable.

Thanks in advance guys, ya'll have been excellent resources in the past!


Top
 Profile  
 
 Post subject: Re: Phono Preamp Wiring
PostPosted: 15 Apr 2020, 05:54 
Offline

Joined: 23 Feb 2017, 02:02
Posts: 677
Because you only have the RCA then it will no accept fully balanced.
You need the high qulity coax cable and if you can, try to match the line impedance when your running long distances.
10M 35ft isn't very long, any coax should work fine without much additonal noise.


Top
 Profile  
 
 Post subject: Re: Phono Preamp Wiring
PostPosted: 15 Apr 2020, 20:51 
Offline
Project Author
User avatar

Joined: 04 Jun 2008, 20:59
Posts: 4285
Location: Arizona, USA
Hi, As long as the preamp has an output impedance that is significantly lower than the input impedance of what it is feeding then it is OK. A ratio between 1 to 5 and 1 to 10 is generally accepted correct. I use "instrument" cable, mostly Belden and Mogami for cables. Several in my system are in the 20 foot range and cause no issues. The biggest issue is loss of high frequency content because of cable capacitance. The more cable the more capacitance. Low impedance sources (like many phono preamps) mitigate this to a large degree. You didn't specify what preamp you got so I really can't be positive and say there will not be some losses. I run ratios about 1 to 25 in my system between the phono preamps and line stage and 1 to 5 between the line stage and power amps.

Good listening
Bruce

_________________
Some of my DIY Tube Amplifier Projects:


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 3 posts ] 

All times are UTC - 6 hours [ DST ]


Who is online

Users browsing this forum: No registered users and 1 guest


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to:  
DIY Tube Projects :: DIY Tube Amp Kits :: DIY Speaker Projects :: DIY Solid State Projects :: DIY IC / Op-amp Projects :: DIY Phono Projects :: DIY Cable Projects :: Hi-Fi Audio Schematics
© diyAudioProjects.com - Terms of Service - Privacy Policy