DIY Audio Projects Forum
 NEW  Matt presents bias and operation data for the 6V6 tube in SE operation - 6V6 Single-Ended (SE) Ultra Linear (UL) Bias Optimization.

DIY Audio Projects Forum

Welcome to the DIY Audio Projects Message Forum. Use these forums to discuss Hi-Fi audio and to share your DIY Audio Projects. Registration is free and required to post messages and view the file attachments. Registration will only take a minute and registered users do not see any advertisements. After you have completed the online registration process, check your email (including spam/junk folder) for the verification email to activate your account. New members are under moderation - so your posts will not be visible until approved by a moderator. See the Read Me 1st, Forum RULES and Forum FAQ to get started on the forum.

It is currently 06 Mar 2021, 17:53

All times are UTC - 6 hours [ DST ]

Post new topic Reply to topic  [ 4 posts ] 
Author Message
PostPosted: 25 Sep 2019, 21:23 

Joined: 25 Sep 2019, 20:48
Posts: 2
Hi everyone, this is my first post. I've got one of these tweeters wired into the front right speaker outputs on an old amp from Goodwill. The amp works fine when plugged into normal speakers, but when there's only a tweeter wired into the amp's right-speaker output, and I play a 1.5 kHz tone at about half volume, after a bit, the tweeter pops, smokes, and fades out.

The setup is:
* a laptop audio out going to the amp's CD inputs
* the laptop plays a 1.5 kHz sine wave
* amp volume dial is about 1/2. The left/right and forward/rear knobs are on the middle.
* the tweeter is impedance matched with the amp (8 Ohms)
* there's not a crossover in front of the tweeter

In trying to characterize the power that the amp is sending to the tweeter, the results were confusing. With a multimeter (or a scope) on the amp-tweeter leg of the circuit, in series it was seeing milliamps, and in parallel, it was seeing millivolts. Since the tweeter is popping and blowing, and the tweeter has a 300W rating, it would seem that the meter should be picking up way more than milliwatts. (This was with the volume knob on the amp maybe a quarter of the way to max volume).

Any ideas for measurements I can try, or any obvious thing I've missed here in the setup?

PostPosted: 07 Dec 2019, 16:21 
User avatar

Joined: 01 Jun 2013, 09:05
Posts: 1051
Its just an idea,

NB as with all things its just suggestions and at your own risk!
If you are wiring the tweeter direct to the amp output its wrong!
It should be fed via a crossover network never direct to the amp output.
The crossover is selective for frequency and is not just about splitting frequencies between midrange and tweeter.
Reason is that the impedance is probably wrong and or there are overtones and spikes appearing on the amp output.
Things like cross over distortion and harmonics.

NB you should never run an amplifier into an open load, if parasitic oscillation sets in it will fry the tweeter and even the amplifier.
Any frequencies that get through to the tweeter that are outside the range of operation will blow it very quickly.
One other thing is I have never seen a perfect power supply so if its not through a crossover you have hum which is the same as low frequency to the tweeter. Without a load on the amp output to sink any transients you could get all sorts of problems.

Another thought, is the tweeter rated at continuous power or transient power. Its not "normal" to run a tweeter at continuous set frequency.

M. Gregg

What is the sound of one hand clapping?

PostPosted: 23 Feb 2020, 22:35 

Joined: 23 Feb 2020, 21:08
Posts: 11
The RMS rating for those tweeters is 150W, a better number than the peak watts for what you are doing, no?

Probably more importantly, the frequency range for those tweeters is 2000hz and above. You were sending 1500hz.

My strong opinion is that no one should ever buy a speaker without seeing a frequency response curve for it. The basic numbers a manufacturer provides can be quite deceptive.

Even if you plan to use a 31 band GEQ or parametric EQ with the speakers, it is best to know the frequency response curve.

For example, check out the curves of two tweeters attached below, GT-324 and GT-510.

The mfgr website lists the 510's response as 3k to 20k, the 324's as 2k to 20k. That is fairly similar. The price at parts express is very similar. ... t-tweeter/ ... d-tweeter/

However when you look at the frequency response curve, sensitivity (SPL) and resonance (Fs) they are quite different!!

The power handling of the two units is similar 50 W for the 510 and 60W for the 324.

However, after fixing the huge bumps in the response of the 324, your SPL will be around 86db. The 510 will be at closer to 93db. Don't you expect the 510 to be louder even though it will handle fewer watts?

Finally it is best to also see a polar frequency response but not all mfgrs provide it. The other attached pic shows the polar response for an old Radio Shack ( Motorola) piezo tweeter. Notice the terrible drop in the highs when you move more than 15 degrees off center!

I successfully used the piezo tweeter in a stage monitor because I could aim it at the seated pianist. The piezo was a good, inexpensive option because it did not require a crossover. It matched quite well with the woofer I selected--a 15" without extended frequency response in the upper mids.

I'm just an experienced hobbyist, not a sound engineer. Others may be able to say more about the specs, for example, the pros and cons of a silk dome vs titanium dome.

So beware of speakers that are sold with minimal specs!

This post has a file attachment. Please login or register to access it. Only Registered Members may view attached files.

PostPosted: 26 Feb 2020, 15:25 

Joined: 25 Sep 2019, 20:48
Posts: 2
Great points. Thank you!

Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 4 posts ] 

All times are UTC - 6 hours [ DST ]

Who is online

Users browsing this forum: No registered users and 4 guests

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to:  
DIY Tube Projects :: DIY Tube Amp Kits :: DIY Speaker Projects :: DIY Solid State Projects :: DIY IC / Op-amp Projects :: DIY Phono Projects :: DIY Cable Projects :: Hi-Fi Audio Schematics
© - Terms of Service - Privacy Policy