DIY Audio Projects Forum
 NEW  Matt presents bias and operation data for the 6V6 tube in SE operation - 6V6 Single-Ended (SE) Ultra Linear (UL) Bias Optimization.

DIY Audio Projects Forum

Welcome to the DIY Audio Projects Message Forum. Use these forums to discuss Hi-Fi audio and to share your DIY Audio Projects. Registration is free and required to post messages and view the file attachments. Registration will only take a minute and registered users do not see any advertisements. After you have completed the online registration process, check your email (including spam/junk folder) for the verification email to activate your account. New members are under moderation - so your posts will not be visible until approved by a moderator. See the Read Me 1st, Forum RULES and Forum FAQ to get started on the forum.

It is currently 24 Jun 2018, 01:56

All times are UTC - 6 hours [ DST ]




Post new topic Reply to topic  [ 1797 posts ]  Go to page Previous  1 ... 176, 177, 178, 179, 180
Author Message
PostPosted: 13 Jun 2018, 04:12 
Offline

Joined: 03 Feb 2018, 00:47
Posts: 18
Location: Brisbane, Australia
I wish I could Poty, but I printed it out at work and failed to send the url to myself. The text says "Recommended changes to the power supply for large Oddwatt amplifiers (EL34 and larger) to use 300VDC on the SRPP Driver tube".
Dated November 12, 2013.

Hopefully somebody can provide the link. It regulates the 300V to the drivers and regulates the "lift voltage" for the heaters using LR8 regulators.


Edit: Found it!!!

http://diyaudioprojects.com/Forum/download/file.php?id=5995&mode=view


Top
 Profile  
 
PostPosted: 13 Jun 2018, 06:29 
Offline

Joined: 24 Oct 2010, 07:05
Posts: 266
Well, it seems the schematic is one of the early experiments with the LR8 and related to the EL34 version. It's only part of the schematic and only the LR8 parts supposed to be used without modifications in all tube's versions.
I'd use unified schematic presented earlier.
Specifically:
- The resistor (its value) depends on the B+ voltage for the power stage. Different tubes have different B+ in the schematic, so there is a way to drop the voltage to appropriate level. So, the bigger the B+ voltage of the power stages - the bigger the value of the resistor.
- The capacitor: there are actually two capacitors. First - is for stability of the LR8 and it could be as low as 1u. Second - for local power supply bypass and Bruce recommends minimum 1uF (I'd use 3.3u or more). It is convenient to use an electrolytics for the first capacitor, but due to their (electrolytics) bigger ESR it is advisable to use much bigger capacitance - 47u or even 100u. The second capacitor for the sound perspective has to be film. To be short: the circuit will work with both "approaches".


Top
 Profile  
 
PostPosted: 13 Jun 2018, 11:55 
Offline

Joined: 18 Jun 2016, 06:52
Posts: 22
Finished. KT77s heated AC, 6SL7s DC. The 12V PSU still needs some fine tuning (optimum dropper resistor values). The sound is positively rich. My layout requires a lot of wiring. It's probably more practical to put the balancing pots and test points on the top plate, but aesthetically less pleasing I think. Comments and criticisms are welcome.

Jan


This post has a file attachment. Please login or register to access it. Only Registered Members may view attached files.



Top
 Profile  
 
PostPosted: 14 Jun 2018, 18:11 
Offline
Project Author
User avatar

Joined: 04 Jun 2008, 20:59
Posts: 3688
Location: Arizona, USA
Hi, Glad to hear it works well. I use that style case for some projects. Hard to beat the price.... shipping is another story though.

Good listening
Bruce

_________________
Some of my DIY Tube Amplifier Projects:


Top
 Profile  
 
PostPosted: 15 Jun 2018, 08:45 
Offline

Joined: 29 Jun 2016, 15:59
Posts: 37
Hi.

Has anybody added an LED to show when the Main B+ kicks-in for the Oddblock?
May 6, 2015 unified schematic.
If so, how?

Thanks,

Danny


Top
 Profile  
 
PostPosted: 15 Jun 2018, 10:13 
Offline

Joined: 24 Oct 2010, 07:05
Posts: 266
Danny, several posts earlier there were answers already, but:
1. Connect a LED+resistor to the low voltage energizing circuit of a relay which switches B+.
2. A resistor from the B+ to the LED to the ground.
3. A CCS from the B+ to the LED to the ground.
4. (if there is enough voltage) Serially connected LED || resistor in the B+ rail at any voltage dropping point.


Top
 Profile  
 
PostPosted: 15 Jun 2018, 12:28 
Offline
Project Author
User avatar

Joined: 04 Jun 2008, 20:59
Posts: 3688
Location: Arizona, USA
Hi Everyone, The Oddwatt amps have evolved over time and I was asked recently for the latest schematics so here they are. They show the latest changes, some are very minor, but each one has what I consider some benefit. Older amps can be retrofitted with the changes fairly easily.

If you use the KT120 version the PS is like the unified version, but no recent changes have been made to the main circuit (no sense messing with something that is OK as is)

Good listening
Bruce
Attachment:
Unified Oddblock Amplifier PS June 2018.jpg
Attachment:
My Odd-Blocks Main Circuit 6-2018.jpg


This post has a file attachment. Please login or register to access it. Only Registered Members may view attached files.


_________________
Some of my DIY Tube Amplifier Projects:


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 1797 posts ]  Go to page Previous  1 ... 176, 177, 178, 179, 180

All times are UTC - 6 hours [ DST ]


Who is online

Users browsing this forum: No registered users and 7 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to:  
DIY Tube Projects :: DIY Tube Amp Kits :: DIY Speaker Projects :: DIY Solid State Projects :: DIY IC / Op-amp Projects :: DIY Phono Projects :: DIY Cable Projects :: Hi-Fi Audio Schematics
© diyAudioProjects.com - Terms of Service - Privacy Policy