| Most viewed |
DIY-Hi-Vi-Tower-Loudspeaker-Project.jpgHi-Vi Tower-Speaker Project10778 viewsTower loudspeaker project using all Hi-Vi drivers. See the DIY Hi-Vi 3-Way Tower Loudspeaker Project page for more info.
|
|
Fostex-FE-103E-Zigmahornets.jpgZigmahornets with Fostex FE103E10656 viewsA pair of DIY FE103E Zigmahornet Speakers with Fostex FE103E fullrange driver.
|
|
Visaton-BG-17-Voight-Pipe-Speakers.jpgVoight Pipe Speakers Visaton BG 17 driver10610 viewsA set of voight pipe speakers built around the Visaton BG 17 full-range speaker driver. The speaker is finished with a decorative bamboo mat finish.
See the Voight Pipe Speakers with Visaton BG 17 build thread on the DIY Audio Projects Forum for more information and photographs.
|
|
Jordan-JX92S-Transmission-Line-Speaker.jpgDIY T-Line Speaker with Jordan JX92S10595 viewsThis is a build of GM's Transmission Line for the Jordan JX92S. More information is available at the Tobler-ONE Jordan JX92S MLTL Speaker Project page.
|
|
Capacitance-Multiplier-Power-Supply-Class-A-Amp.jpgCapacitance Multiplier Power Supply For Class-A Amp10579 viewsUsing Rod Elliot's Capacitance Multiplier Power Supply with Mark's DIY Class-A 2SK1058 MOSFET Amplifier.
This is a big improvement in heat dissipation, but I still may make more improvements to make it run cooler though.
|
|
Low-Inductance-DIY-Speaker-Cable.jpgDIY Low-Inductance Speaker Cables10485 viewsSimple cable design that uses four 16 gauge wires which result in an equivalent 10 AWG cable. The wires are twisted together in opposite directions which helps keep inductance of the overall speaker cable to a minimum. See the Low-Inductance DIY Speaker Cable project page for full details.
|
|
DIY-2SK1058-Mosfet-Amp-Inside.JPG2SK1058 Mosfet Amplifier - Inside10349 viewsSergiy Makharchuk build of Mark's simple DIY Class A 2SK1058 Mosfet Amp Project. Here Sergiy has used light bulbs in place of the load resistor. The enclosure is recycled from an old piece of physiotherapy equipment.
|
|
Fostex-FX120-Baffle.jpgFostex FX120 Drivers on Baffle10328 viewsFostex FX120 Fullrange Drivers mounted on the 1" thick MDF Baffle that came with the prefab cabinets.
|
|
Fostex-FE126E-Bass-Reflex.jpgFostex FE126E in DIY 12L Bass Reflex Cabinets 10306 viewsThese are a small pair of 12L Fostex FE126E in 1/2" solid pine BR enclosures. The port is 2" x 4". They do sound great though with surprising bass from the FE126E. They are 9.5" square...I know square...but I found it helps reinforce the bass.
|
|
Fostex-FE167E-Bookshelf-Speakers.jpgDIY Fostex FE167E Bookshelf Speakers in Listening Room10202 viewsA pair of DIY Fostex FE167E Bookshelf Speakers in the Listening Room.
By Gary E (MN, USA)
|
|
Cotton-ConneX-DIY-Interconnect-Cables.jpgCotton and Silver DIY Interconnect Cables10193 viewsThese are the Cotton ConneX DIY Interconnect Cables which are very similar to the DIY Silver Interconnect Cables. The Cotton ConneX are solid Silver wire with Cotton insulation. These were hard to make as the cotton continues to fray. These were well worth the effort as the produce a different and enchanting cable.
|
|
Copper_Steampunk_K-12GTube_Amplifier_Kit.jpgCopper Steampunk K-12G Tube Amp Kit10122 viewsThis is a K-12G tube amplifier kit that I built into a steampunk-ish enclosure. Had a blast with this one, and I'm amazed at the amount of wonderful sound that this little tube amp kit puts out!
I'll be posting construction photos on my blog site if you're interested in taking a look: www.coppersteam.com
Mike Cochran
Key West, USA
|
|
DIY-Phono-Turntable-2.jpgDIY Turntable Project10094 viewsDIY turntable project. I used MDF filled with concrete / latex added to mix then veneered with Quilted Maple. The bearing is High grade SS and the cup is made of Oilite. The spikes are 2 piece with a rubber damper inside. The Motor is powered by a UPS battery enclosed in the small matching box.
Doug M
|
|
S-5-Electronics-K-12G-Tube-Amp-Kit-front.jpgS-5 Electronics K-12G Tube Amplifier Kit - front view9963 viewsFront view of enclosure for a S-5 Electronics K-12G Tube Amplifier Kit.
|
|
Fostex-FX120-BR.jpgFostex FX120 in Bass Reflex Enclsoure9938 viewsHere is a front and rear view of the finished Fostex FX120 Bass Reflex Bookshelf Speakers. The cabinet size is about 0.38 ft^3 and tunned to about 63 Hz. See the page for more information.
|
|
Fonken-Fostex-FE127E-Speaker.jpgFonken Speaker Enclosure for Fostex FE127E9864 viewsA pair of Fonken speaker cabinets for the Fostex FE127 fullrange driver. So far they sound very nice.
|
|
Open-Baffle-Speaker-Fostex-FE206E-Eminence.jpgFostex FE206E / Eminence Open Baffle Speaker System9823 viewsThis open baffle speaker system is the latest creation from Keith's of Kickwood Audio. The drivers are the Fostex FE206E fullrange speaker and a 15" Eminence driver. Very nice looking and they sound as good as they look.
|
|
DIY-Hi-Vi-MTMW-Tower-Loudspeakers.jpgDIY Hi-Vi MTMW Tower Loudspeakers9789 viewsDaniel from Canada has complete a build of Adam's DIY 3-Way Hi-Vi Tower Speaker Project. More pictures and info about Daniel's experience with this project is available at his website.
|
|
Sansui_1.JPGSansui AU-X11 (rare)9786 viewsThe Melbourne Audio Club Australia has many talented members. Some sell commercially, all over the world, there own brands others DIY for themselves while still others take it on themselves to restore "better" commercial units. This member has restored this (I'm told) rare Sansui AU-X11. It certainly looks impressive.
|
|
FE103E-TQWT-speaker-package.jpgTQWT for the Fostex FE103E9779 viewsA nicely finished Tapered Quarter Wavelength Tube (TQWT) Loudspeaker from Japan. The enclosure is for the Fostex FE103E Fullrange Speaker driver.
|
|
| 614 files on 31 page(s) |
 |
3 | |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
